DEMO PAGE

The Easy Bracket Saddlebag Bolt-on Support System is quick and easy to install.  The installation is usually completed within one hour.  Typically you will need the following tools to complete the installation.

• Drill and 3/8” drill bit
• Open-end wrench to tighten the Nylon locking nuts and bolts.
• Allen wrench for button head or socket head bolts
• Black marker or similar marking device.

The following instructions are to be used in conjunction with the installation instructions provided with each model of Easy Brackets. For the purposes of this demonstration we are installing the Easy Bracket system onto a Harley Davidson Softail.  Any variations from this installation will be explained in the installation instructions provided with each individual model of Easy Brackets.

Before you begin the installation of your Easy Brackets, read the installation instructions provided with your kit and verify all specified parts are included in your kit.

Your are now ready to begin the installation of your Easy Brackets.

STEP 1

Starting on the right-hand side of the motorcycle, the throttle side, remove and replace the stock fender bolts with the bolts and docking posts provided in the kit.  It is highly recommended you remove and replace one bolt at a time to avoid movement of the fender during the installation. 

STEP 2

Install the Easy Bracket onto the docking posts.  Verify you have the correct Easy Bracket labeled right side.  The lock must be in the open position prior to installing the bracket onto the docking posts.  The lock must be locked before the key can be removed. 

The cam, (the part of the lock that fits under the docking post) must be completely under the docking post for the lock to be fully locked.  The cam will contact the back of the saddlebag after the saddlebag is attached to the bracket as explained in step 4.  Please note the cam only needs to clear the docking post for removal and will not rotate a complete 90 degrees.

If the Easy Bracket does not seat completely to allow the cam to fit under the docking post, proceed with the following alignment process.

• With the Easy Bracket mounted onto the docking posts and the lock in the open position, loosen each bolt slightly to allow movement of the docking posts.
• Next, gently shake and push the Easy Bracket down onto the docking posts.  This will create a proper alignment between the docking posts and the keyholes in the bracket.
• Place the lock in the locked position with the cam positioned completely under the docking post.  Retighten the fender bolts.
• Remove and reinstall the bracket to insure ease of installation and removal.  You have completed the alignment process.

STEP 3

Next, with the bracket mounted to the docking posts on the motorcycle, hold the saddlebag up to the bracket and position it to the desired location.  Note the clearances from the seat, turn signals and any lower obstructions such as chain guards, axle nuts, exhaust pipes and etc.  After the desired location is achieved, with a black marker or similar marking device, mark the outer edge of the bracket on the saddlebag.  Remove the Easy Bracket from the motorcycle.

STEP 4

Next, lay the saddlebag on its side with the back facing up.  Position the bracket on the saddlebag within the outline marked in step 3.  Using the black marker, mark the location of the (4) mounting holes onto the back of the saddlebag. 

Remove the bracket from the saddlebag and drill the mounting holes into the saddlebag using the drill and 3/8” drill bit.  Next mount the Easy Bracket to the saddlebag using the (4) 3/8” black button head bolts, fender washers and nylon locking nuts.  The fender washer is located on the inside of the saddlebag.

STEP 5

Finally, mount the saddlebag with the Easy Bracket onto the motorcycle.  If the bracket is properly mounted onto the docking posts the keyed lock will fully engage and you may remove the key.

You are now ready to repeat these instructions on the left-hand side of the motorcycle.

For product support, damaged or missing parts, please contact Great Bike Gear, Inc. at 866-521-3024.  Do not return product without prior authorization.

Why Easy Brackets Bolt-on Saddlebag System?

• Allows you to mount your saddlebags without damaging the paint on the rear fender which can often happen with throw-over saddlebag style mounts.
• Convenience of a quick-release mechanism which turns your saddlebags into portable pieces of luggage.  A must if you road trip frequently and works great with our Easy Tote.  
• Kits are made especially for the motorcycles.  Forget the hassles from 'Universal' or 'Adjustable' kits that offer less than an ideal fit or make it difficult to line up the docking posts properly.
• Clean look when you remove the bag.  No ugly hardware left behind.
• With some motorcycle models, you can avoid conflicts with high shotgun pipes.
• Superior design - enclosed locking areas, covered barrel locks and covered side panels that help keep road grime out and increase the durability and long-term functionality of Easy Brackets versus other popular models.
• Lower Incline Angle - Other popular saddlebag bolt-on systems have a 10 degree angle, making the bags stick out too far from the motorcycle.  The Easy Brackets have a smaller 5 degree angle, making the bags sit more flush to the motorcycle for better looks.